NanoVNA VNA HF VHF UHF Vector Network Antenna Analyzer + 4.3 LCD + Metal Case. Support measurable frequency to 1.5 GHz, default setting 1 GHz, accurate measurement up to 1.35GHz. Added reactance trace, testing with. CQ CQ CQ, This is.Brave Hotel Five Hotel Novemter Uniform. The original author of NanoVNA-F. NanoVNA-F "Handheld Vector Network Analyzer". A product based on the Open Source Project of NanoVNA. Thanks to hugen's creative idea of use the harmonic of Si5351. We build NanoVNA-F and expand the measure frequency up to 1GHz, which S11 still have 40dB dynamic range At 1GHz. Ask any questions about NanoVNA-F. NanoVNA-F hardware features include and are not limited to the following improvements. Use 4.3-inch IPS TFT LCD &. With a larger view angle and can be seen clearly in strong outdoor light. The battery is an optional accessory, some. Standby time is longer, and expand a USB interface.
Usually, it can be used as a power bank when the instrument is not used. The Lipo Charing IC to changed to IP5306with 2A.
Make the charging time shorter. Use a larger and better operating level.Use a larger and better operating Power Switch. Support Chinese and English menu switching. Upgrade the user program by virtual U disk16MB SPI Flash Memory Inside. Standard aluminium shell to protect SMA head and reduce the interference of external electromagnetic wave to instrument. Firmware are fully open source at.
The NanoVNA-F measurement range is 50k-1GHz. Use the harmonic of the clock chip SI5351 the.
At 600M-1GHz, the S11 has a dynamic range of 40dB (the standing wave ratio is less than 1.02). The RF front end is designed with a metal shield that allows the S21 to have a dynamic range better than 60dB over the full frequency range. Size: 14CM 7.5CM 2CM (length, width and height).RF output: -13dbm (maximum -9dbm). Display: 4.3 inch IPS TFT (800x480). USB interface: USB Type-C communication mode: CDC (serial). Power consumption: USB 5V 200mA, built-in 5000mAh/3.7V battery, theoretical battery life 18 hours, maximum charging current 2A.
Number of calibration points: 101. Number of scanning points: 101. Display Tracking: 4, Marking: 4, Setting Save: 5.
Scanning time: about 1.9s/1 times (50kHz 1000MHz full frequency band). Can measure S parameters, voltage standing wave ratio SWR, phase map, group delay, Smith chart..Original 19.0Wh (about 5000mAh/3.7V after conversion) large capacity lithium battery. Designing a metal shield for the RF front end, allowing the S21 to have a dynamic range better than 60dB over the full frequency range. Open Coaxial cable length measure.
1, NanoVNA-F S11 parameters, SWR standing wave ratio measure. WOUXUN UV9D-Plus antenna UHF standing wave ratio measurement, starting frequency: 300M, stop frequency: 600M, the green curve in the figure below is the standing wave ratio, the lowest frequency of the standing wave is at 444.000000MHz, SWR=1.03. UV9D-Plus antenna interface is an SMA standard male (internal screw) that can be directly connected to the instrument or connected via the included SMA elbow for easy testing.
Baofeng UV-5R VHF antenna VSWR measurement, the antenna interface is SMA standard female, can be connected to the instrument through the attached SMA-JJ adapter. The lowest point of the standing wave is 134.200000MHz, SWR=1.68. 2, S21 insertion loss measurement, low pass, high pass, band pass filter measurement. Measuring 6.5M Ceramic Notch with NanoVNA-F.Measuring 10.7M ceramic filter using NanoVNA-F. A self-made low-pass filter was measured using the NanoVNA-F with a 3dB bandwidth of approximately 400MHz. Keysight E5071C four-port vVector network analyzer vs NanoVNA-F. R433 Surface-Acoustic-Wave Resonator Measurement Comparison.
The actual frequency response curve in the. The real measurement result of NanoVNA-F, the blue curve is S21, and the transmission measurement (insertion loss). RX: 480M TX: 505M Keysight E5071C four-port network.
LoRa U Band duplexer measure comparison. RX: 480M TX: 505M NanoVNA-F.
S11 U Band duplexer data comparison, E5071C(501 points) vs NanoVNA-F1. S21 U Band duplexer data comparison. E5071C(501 points) vs NanoVNA-F1.
It can be seen that after calibration, NanoVNA-F can get good measurement results. SMA-JJ RG316 cable 20CM x2. NanoVNA-F is a standard SMA female connector, external screw inner hole, use this cable to switch to M head, N head to better protect SMA female. 1 set of calibration parts.
If you change the measurement conditions, such as adding a patch cord and modifying the frequency range, you may need to recalibrate and store the parameters in 0-4. All parameters can be called up by the "recall" function. SMA elbow, external screw inner hole to inner screw inner needle x1.
NanoVNA-F Quick Start Guide x1(English). At the same time, To. A set of packing boxes with EPE protection equipment and parts is included.
Display test of LCD screen under sunlight. After Firmware v0.0.3, NanoVNA-F support PC control softwares build for NanoVNA.NanoVNASharp v1.0.3(by Hugen). NanoVNA-F Menu Structure Quick start guide. SMA-JJ RG316 cable 20CM x2 (NanoVNA-F is a standard SMA female connector, which is used to switch to M head and N head to better protect SMA female). 1 set of calibration parts 50? Standard load x1, open circuit calibration piece x1, short circuit calibration piece x1, use the included calibration piece, the instrument can be calibrated to get good measurement result data. SMA elbow external screw inner hole to inner screw inner needle x1. Please make sure it is correct.
We believe our items are so outstanding. All products are quality checked. We will be happy to resolve any issues you may have in a cordial and friendly manner. We appreciate your Postive Feedback, and will do the same in return. The item "50KHz-1000MHz NanoVNA-F 4.3 LCD Display HF VHF UHF VNA Vector Network Analyzer" is in sale since Tuesday, September 3, 2019.This item is in the category "Business & Industrial\Test, Measurement & Inspection\Analyzers & Data Acquisition\Cable & Antenna Analyzers". The seller is "2012moon816" and is located in ShenZhen ,Guangdong. This item can be shipped worldwide.