Icom IC-R9500 Professional Comm Receiver. 005-3335 Mhz, UT-122, SP-20 & Manual

  
Icom IC-R9500 Professional Communications Receiver. This is an exceptional Professional Communications Receiver with 0.005 to 3335MHz Coverage (Cell Blocked) and a High-Performance Spectrum Scope. This complete system includes the UT-122 for P-25 Digital, WRTH Frequency Guide, Icom Manual, original Power Cable, and the matching SP-20 Speaker for great audio. Listed in current production on the Icom website but unavailable at every outlet that I checked (Ham Radio and Comm Outlets). We cleaned the case & controls, installed a new CMOS/Memory Battery and tested it on the BC band with a small loop antenna. It hears very well and is easy to use. This is an outstanding receiver that easily outpaces the OMs Kenwood TS-890s. The display is bright with great clarity. Internally, the receiver is immaculate - only the lightest dust was found and cleaned out.

Extremely minor wear with light case scratches as seen in the pics. Hitting the Digital Mode selects and highlights P25, so we assume that the UT-122 is installed. We did not take the unit apart to visually inspect the module. Thanks for dropping by 73 (Best Wishes) Roberta.

Information from the Icom Website. Professional Communications Receiver with 0.005 to 3335MHz Coverage and High Performance Spectrum Scope. +40dBm 3rd order intercept point and 109dB dynamic range. Multi-function high performance spectrum scope. ±0.05ppm high frequency stability. Accuracy of dBµ/dBµ(emf) /dBm meter. 10 to 70dBµ signal between 100kHz to 3335MHz at 25°C. Optional P25 digital mode reception. Professional grade operation, functionality and build. It is suitable for a wide variety of radio monitoring and listening activities. Optional UT-122 digital unit is required. The IC-R9500 achieves amazing performance by using a D-MOS FET array in the 1st mixer (below 30MHz) and an excellent IMD roofing filter. The IC-R9500 has +40dBm IP3 and 109dB dynamic range at 14.1MHz. IP3 performance is +9.8dBm at 50MHz and +6.2dBm at 620MHz +5dBm (typical) from 30MHz to 3335MHz. The IC-R9500 has 5 independent roofing filters (240, 50, 15, 6 and 3kHz) for improved selectivity.

In very crowded RF spectrum conditions, it is extremely important to protect against strong in-band signals. The 3kHz roofing filter provides a 130dB approx. At 15MHz reception, with 5kHz separation signals. The IC-R9500 incorporates two independent, 32-bit floating point DSP units, a dedicated DSP unit for receiver functions and another for the spectrum scope. By using the power of two independent DSP units, the radio can respond to operator changes in an instant.

±0.05ppm High Frequency Stability. The IC-R9500 uses an OCXO (Oven Control Crystal Oscillator) unit which provides ±0.05ppm frequency stability from 0°C to 50°C. The 10MHz reference frequency can either be supplied to or input from external equipment. Allows the operator to adjust the filter shape (sharp or soft), filter bandwidth, and center frequency characteristics. The digital twin PBT narrows and shifts the IF passband to efficiently eliminate undesired signals.

For FM, WFM and P25 mode, the passband width is fixed. Using a dedicated DSP unit improves the dynamic range of the spectrum scope. The IC-R9500 has four different spectrum modes such as normal/wide and center/fixed width.

The normal spectrum scope covers a range from ±2.5kHz to ±5MHz, while the wide band spectrum scope. Observes up to ±500MHz (±10MHz, ±25MHz, ±50MHz, ±100MHz ±250MHz and ±500MHz selectable). When using the normal spectrum scope, the digital scope's filter width can vary from 200Hz to 20kHz with a variable sweep speed.

The spectrum scope can also be set to use specific scope edges or to center the span on the receiving frequency. The peak search function automatically moves the display marker to the strongest signal on the scope screen. In addition to these features, the scope has 3 levels of attenuation (10dB, 20dB, 30dB). While using the wide band scope function, AF output is muted.

The scope screen does not shift when you change the receiving frequency. The scope screen shifts as the receiving frequency moves. The receiving frequency is always centered on the scope screen. Wide band scope receives up to ±500MHz.

Sweep speed/span/ filter width setting. 7-inch Wide Color TFT LCD. The large 7-inch wide (800 × 480 pixels) active matrix display delivers quick response time, high resolution and has a wide viewing angle.

The multi-function spectrum scope is displayed in vivid color. The background color is selectable from black or blue for your preference. In addition, the IC-R9500 has a VGA connector allowing you to connect an external monitor. S-meter, dBµ, dBµ(emf) and dBm meter types are selectable in the IC-R9500. The dBµ, dBµ(emf) and dBm meter have ±3dB of accuracy (10 to 70dBµ signal from 100kHz to 3335MHz at 25°C).

The IC-R9500 has the DSP controlled noise blanker that significantly reduces pulse type noise and improves the S/N ratio by removing interfering noise. The noise blanker has two channels with adjustable width and depth parameters. You can use these to target the specific noise interference. The digital manual notch filter has a depth of more than 70dB at two points with adjustable filter width (wide, middle, narrow).

This means that two strong beat signals can be eliminated at once even while using the auto notch filter. This mode is useful when fading occurs or signal level is low. The IC-R9500 can recreate the carrier signal exactly by using the DSP. The IC-R9500 has built-in FSK demodulator and decoder.

FSK tone and shift frequencies programmable. The IC-R9500 has 10 VFO channels for tuning and storing operating frequencies, mode, filter width and other settings. For example, use VFO-1 for the 7MHz band, VFO-2 for the VHF marine band, VFO-3 for the 1200MHz band, etc. You can quickly change the operating bands with the 10-keypad.

When the VFO is changed, the settings are automatically stored in that VFO channel. A total of 1220 Memory Channels. The IC-R9500 has a total of 1220 memory channels. Store frequencies, modes, filter width and tuning steps. Memory channels are grouped into 10 memory banks.

By connecting to a USB keyboard, you can edit memory contents directly. 100 auto memory write channels. 100 memory scan skip channels.

The IC-R9500 has two types of digital voice recorders. One is the regular recorder, recording for long periods in "WAV" format into the built-in CF memory or an external USB memory. The sampling rate is variable from 8kHz (SQ1) to 48kHz (SHQ).

In SQ1 mode, up to 130 minutes approx. Of recorded audio can be stored into the CF memory. The other recorder is the shor t voice recorder, which saves the previous 15 seconds of radio audio into RAM, allowing you to play back the audio instantly. Numerous scanning functions to search for desired stations are available to make operation easier. The IC-R9500 scans 40 channels per second in memory scan mode.

F scan / F fine scan. The built-in synthesizer announces the receiving frequency, mode and signal strength in English. The IC-R9500 has a USB connector for connecting external USB memory or other USB devices.

Received audio and the receiver configuration files can be imported and exported to a PC. Firmware upgrades are also possible via USB memory. Some functions are not available depending on operating mode or band. AFC function compensates for frequency shifts(FM/WFM mode only). Input overload protection (HF bands only).

4 antenna connectors: an SO-239 type, a phono (RCA) connector and two type-N connectors. Clock function with daily timer and sleep timer. CTCSS and DTCS tone squelch.

Simplified frequency calibration using WWV or WWVH. They are taken with a professional camera (Nikon) and can be zoomed to show the detailed condition of the item. Examine them closely as they depict the actual condition of the item. See the condition statement for clarification. Additionally, I honor requests for additional photos. Prior to sale, all Items are stored in a climate-controlled & smoke free storage facility in south-central (dry) Texas. Most items are treated to remove odors, some dust/dirt, residue and bacteria/virus. Detailed cleaning, alignment, firmware upgrade, modification removal and maintenance is left to the new owner. We re-use/recycle packing materials, boxes, bubble-wrap and unwanted furniture foam whenever possible. Original boxes, manuals, accessories, and packing are not included if not described and pictured.

Test equipment, accessories not specifically identified in the item description, and other items pictured are not included. Paper items, manuals, & instructions may have writing, stains, creases and/or some pages may be torn/missing.

Some may have additional notes, updated information & information not pertaining to the equipment it is supposed to cover. Written material is not included if it is not listed in the description.

Computer media, software, firmware, compact discs, drives is not normally tested & not warranted. Complex equipment or items that require additional cables, manuals, software and/or equipment are tested by built-in test equipment, if available, and on-site capability only. See the item description for tested functions. Vintage electronics items are frequently repainted, and the quality and condition may vary from the original finish.

Items may have been in a smoking environment at some point in their history. Modifications and non-original parts may be installed in this equipment. Battery powered equipment may have had battery leaks/issues in the past. HT batteries are normally the vintage of the radio and should be expected to perform as age appropriate, i. Removeable batteries, Built-in chargers, power supplies and CMOS (memory batteries) are untested & unwarranted.

A replacement battery may be required to meet user expectations. Consider all items to be used and show signs of use.

This may include scratches, wear, chips, cracks, corrosion and dust. In order to meet your full expectations these items may need tune up, cleaning, replacement batteries (internal & external), indicator or meter lights, accessory items, vacuum tubes, dial cords, cables & other accessories, manuals and/or instructions and other minor items/adjustments/repair/parts. Basic functions are tested, where possible, but not all functions are tested. Basic functions are detailed in the description above and are the only warranted functions of this item. Hams will be hams - Prior owners may have performed mods, updates or repairs that were not noticed or described. Computer connectivity Rig control, D-Star, C4FM, DMR etc. Is normally untested and unwarranted due to the differing software required for internet capable products. Frequently on applicable electronics, the new owner will need to perform required software upgrade(s). Thanks for stopping by es 73 (best wishes) Roberta.